![]() You'll need them anyway, the truck wheels are another that take a large size socket, Expert Reply: The spindle dimensions are as follows: A is the mounting dimension, B is the seal dimension, C is the inner bearing surface, D is the outer bearing surface and E is the diameter of the threaded portion of the spindle for spindle nut selection. Drive, Ford, Not for Use with Impact Wrenches or Power Tools, Each. China best bass octave pedal +81079 Castle nut size refers to its nominal thread diameter. Thread Size: 2-7/8 inch-12 Outside Diameter: 4.130 inches Thickness: 0.375 inch Automann Number: 209.2317. Does anyone know offhand the size socket you need for the S-Series front axle nut? 1-3/4 - 12 UNF. ![]() ![]() I know they are close, but I only want to purchase one socket for the job! Acura RDX Axle Nut Size. 34/35/36mm? It's the right size and it's 1/2" drive so no need for an adapter: This replacement front spindle nut / washer kit fits 41-45 MB. ![]() When it comes to your Ford F-350, you want parts and products from only trusted brands. What size is the spindle nut on a Dexter Axle? Searched but couldn't pinpoint it. Bosch Automotive Service Solutions 28635 Mound Road, Warren, MI 48092 USA. This replacement 2-1/16-inch spindle nut socket fits the. Install a spring scale to one of the wheel nut studs. ft.) Rear hub: 30 mm nut tightening is a 2-stage process: - first tighten to 35 NM (25 lb. Put Axilok in the correct size six-point socket (refer to Table 1) and verify that the locking clips are compressed. I believe they're like a 1-1/4 or 1-5/16. The most common lug nut sizes are: 10mm x 1.25. The nut is for the tension on the wheel bearings, and even though your wheel bearings should be tightened quite snug, the nut should not be tightened real hard. Say you need a spindle and hub for a wheel with 5 on 4-1/2 inch bolt pattern and an axle. Component Bolt Size Hub bearing retaining bolts: 14mm, 12pt: Lug nuts: 19mm: Axle shaft nut: 1 11/16" Upper ball joint nut: 1" Lower ball joint nut: 1 1/8" Transfer case and all drain. You tend to find three standard sizes, although there are others available. The owner must receive a Return Goods Authorization (RGA) Number before returning any product.It's a good idea to have a number of " drivers at your disposal. Mile Marker representatives will work to resolve any warranty issues. You can view the full details of Mile Marker’s warranty here.Ĭontact Mile Marker directly by calling 1-80. Any alteration of products will void the warranty. Misuse, abnormal use, finish, damage from accidents, corrosion, improper installation, incorrect applications. There is no applicable warranty after initial use. New cable assemblies are warranted against defects in workmanship and materials when received by the retail purchaser. On the Four-Wheel Drive Chain included in some kits. Electrical components consisting of motors, solenoids, wiring, wire connectors.Mile Marker Hub Conversion Kits and Transfer Case Conversion Kits. ![]() Hub Part Numbers 427, 428, and all “Selectro Classic” models.On hub Part Numbers 460, 426, 438, and Electric Winches. If you discover a hidden defect, Mile Marker will, as its option, repair or replace the product or necessary replacement parts at no charge to you, provided you remove the product from the vehicle and return it prepaid to Mile Marker Inc. Warranty registration cards for each product must be submitted at the time of purchase or within 30 days by the end user. Mile Marker warranty its products against defects in material and workmanship appearing under normal use and service for the periods below. ![]()
0 Comments
Leave a Reply. |